You have no items in your cart.

More Views

Close X

Scanmaster 1520 Pro Quad Metal Detector

Sku: 129-2022
Retail: $1,500.00
Now Only: $1,199.00
More Range, Better Discrimination and Utilizes the Same Quad Collector System Offered on Other "High-End" Series

Availability: In stock

We accept Wire/Bank transfers - call 888-535-5926

Scanmaster 1520 Pro Quad Metal Detector
More Range, Better Discrimination and Utilizes the Same Quad Collector System Offered on Other "High-End" Series

The newest offering from the Scanmaster has more range, better discrimination and utilizes the same Quad Collector system offered in their "high-End" 1550 series. You will get better filtering of unwanted targets. The advanced main unit is lightweight and simple to use and there is no guesswork involved in the operator’s part. Discrimination of unwanted targets is a simple turn of the frequency knob. All controls are clearly identified so that adjustments can be made quickly. The operating range of the 1520 Pro Quad is very good with some targets being detected at over a half mile away.

Additional Information

Not currently available.

Scanmaster 1520 Pro Quad Metal Detector

Now With (4) Quad Collectors

To explain the basic concept of the Omnitron scanners, one must first understand some very important basic facts. Instrumentation implementing electromagnetic induction, RF induction, and gamma wave transmissions were thoroughly tested. Much was learned about the effects of magnetics and ionization on all phases of matter. Much of what was discovered was applied in developing the original scanner. What was really unique was that the scanner had the ability to utilize air, oil or water as the transmission media. Not only was the signal broadcast in a strictly horizontal direction, but also in a spherical direction. One can only imagine being the center of 3/4 mile sphere with that sphere being your probable target area!

scanmaster 2004 Now once the signal is transmitted by the scanner, the prospective target then reciprocates with a complimentary and identical signal. Because of the fact that the signals are identical, only that element is being "tracked" by the scanner and thereby eliminating the event of tracking unwanted targets.



Below is How Scanmaster Sytems Work:
Scan and Search up to 3/4 Mile to Pinpoint your Target!
Crossed Rods Indicate Target
Move Collector Rods Closer to Locate Target
Final Scan
Easy to Locate Target

The reciprocating signal between the scanner and the target now becomes the traceable roadway for the operator to locate the target. This process requires only several minutes to determine if there are any suitable targets within the normal operating range of the scanner. Please remember that the range depends on the size of the buried target, signals are RF by nature, heavy solar activity will diminish the signal to a small degree.

Power Transducer
This unit is responsible for delivering the selected signal of the Scanner to the ground plane of the strata via the two copper legs which are plugged into the ground. The coax lead is the power supply line and attaches to the output of the Scanmaster. Now you can locate target at 1/2 miles or more.

Advanced Power Module
This unit's purpose is to power the Antenna Rods. The unit contains a 9VDC battery for a power supply. The battery condition is displayed when the Push Button on top is pressed in. If the top indicator light is bright, the battery is okay. If is is dim or out, the battery needs replaced. To replace the 9 volt battery, simply open the module by rotating the bottom cap off. The power module is turned on when the receiving Antenna Rods are plugged in the Power Module's receptacle. When not in use, unplug the Rods from the Power Module! Storing the Power Module with the Rods plugged in will drain the 9 volt battery. Do not allow the Rods to touch each other while attached to the module as this will short out the battery also!

Receiving Antenna Rods
The rods are powered by the Power Module. The purpose of the Rods is to indicate to the Operator that he or she has walked into the transmission line between the Power Transducer and the Target. The rods are normally held steady and balanced at waist level, and slightly in front of the Operator. They are held pointed in a forward direction parallel to each other, and at a distance of 8 to 18 inches apart. What each individual needs to discover is just what distance best relates to themselves. This decision will be by trial and error. Please remember that an individual who is relaxed and calm will operate the equipment more successfully than one who is tense and rigid. The rods will cross naturally by themselves when you enter the RF Energy line. When it first happens for you, you will learned to anticipate success and will welcome it when it happens!

Collectors
These four devices are used as passive repeaters to aid in pinpointing the location of targets. They are "passive: in that they require no power supplies and simply pick up the Scanner's initial signal and pass it on to the target. Initially, the primary pair are used to triangulate in on the target. Once the area surrounding the target is localized, the secondary pair are used to pinpoint that target.

Features
  • Power Module
  • Power Transducer
  • (4) Quad Collectors
  • One Set of Receiver Rods
  • Upgraded Pelican Carry Case
  • Complete Easy to Follow Instructions
  • Advanced Micro Scanmaster Main Unit
  • Operates on (2) 9 V Batteries
  • Longer Detection Range up to 1/2 Mile or More!
  • Limited Lifetime Warranty on Main Scanner Unit Only (call for details). 90 Day Warranty On All Other Components
Customer Reviews

This product has no reviews. Be the first to write one!

Garrett Metal Detectors
Minelab Metal Detectors
White's Metal Detectors
Nokta Metal Detectors
Teknetics Metal Detectors
Fisher Metal Detectors
Tesoro Metal Detectors
Quest Metal Detectors
Aqua Scan Metal Detectors
Bounty Hunter Metal Detectors