 NEW!
Scanmaster 1520 Pro Quad
Now With (4) Quad Collectors
The
newest offering from the Scanmaster has more range, better
discrimination and utilizes the same Quad Collector system
offered in their "high-End" 1550 series.
You will get better filtering of unwanted targets. The advanced
main unit is lightweight and simple to use and there is no
guesswork involved in the operator's part. Discrimination
of unwanted targets is a simple turn of the frequency knob.
All controls are clearly identified so that adjustments can
be made quickly. The operating range of the 1520 Pro Quad
is very good with some targets being detected at over a half
mile away. Includes upgraded Pelican hard-shell carry case.
 Longer Detection Range up to 1/2 Mile or More!
Features:
Advanced micro Scanmaster main unit; (4) Quad
collectors; one set of receiver rods; Power module;
power transducer; upgraded Pelican carry case; Complete easy
to follow instructions; Limited Lifetime warranty on main
scanner unit only (call for details). 90 Days on all other
components. Operates on (2) 9 Volt batteries.
To
explain the basic concept of the Omnitron scanners,
one must first understand some very important basic
facts. Instrumentation implementing electromagnetic
induction, RF induction, and gamma wave transmissions
were thoroughly tested. Much was learned about the effects
of magnetics and ionization on all phases of matter.
Much of what was discovered was applied in developing
the original scanner. What was really unique was that
the scanner had the ability to utilize air, oil or water
as the transmission media. Not only was the signal broadcast
in a strictly horizontal direction, but also in a spherical
direction. One can only imagine being the center of
3/4 mile sphere with that sphere being your probable
target area!
Now
once the signal is transmitted by the scann, the prospective
target then reciprocates with a complimentary and identical
signal. Because of the fact that the signals are identical,
only that element is being "tracked" by the
scanner and thereby eliminating the event of tracking
unwanted targets.
|
Below
is how Scanmaster Sytems work:
Scan and Search up to 3/4 mile to Pinpoint your
Target! |
|
Crossed
Rods Indicate Target |
Move
Collector Rods Closer to Locate Target |
Final
Scan
Easy to Locate Target |
|
|
|
The reciprocating signal between the scanner
and the target now becomes the traceable roadway for the
operator to located thetarget. This process requires only
several minutes to determine if there are any suitable
targets within the normal operating range of the scanner.
Please remember that the range depends on the suze of
the buried target, signals are RF by nature, heavy solar
activity will diminish the signal to a small degree.
Longer Range Advanced Power Transducer
Power Transducer--
This unit is responsible for delivering the selected
signal of the Scanner to the ground plane of the strata
via the two copper legs which are plugged into the ground.
The coax lead is the power supply line and attaches
to the output of the Scanmaster. Now you can locate target at 1/2 miles or more.
Advanced Power Module
-- This unit's purpose is to power the Antenna Rods.
The unit contains a 9VDC battery for a power supply.
The battery condition is displayed when the Push Button
on top is pressed in. If the top indicator light
is bright, the battery is okay. If is is dim or
out, the battery needs replaced. To replace the
9 volt battery, simply open the module by rotating the
bottom cap off. The power module is turned on
when the receiving Antenna Rods are plugged in the Power
Module's receptacle. When not in use, unplug the
Rods from the Power Module! Storing the Power Module
with the Rods plugged in will drain the 9 volt battery.
Do not allow the Rods to touch each other while attached
to the module as this will short out the battery also!
Receiving Antenna
Rods-- The rods are powered by the Power Module.
The purpose of the Rods is to indicate to the Operator
that he or she has walked into the transmission line
between the Power Transducer and the Target. The rods
are normally held steady and balanced at waist level,
and slightly in front of the Operator. They are
held pointed in a forward direction parallel to each
other, and at a distance of 8 to 18 inches apart.
What each individual needs to discover is just what
distance best relates to themselves. This decision
will be by trial and error. Please remember that
an individual who is relaxed and calm will operate the
equipment more successfully than one who is tense and
rigid The rods will cross naturally by themselves
when you enter the RF Energy line. When it first
happens for you, you will learned to anticipate success
and will welcome it when it happens!
Collectors
-- These four devices are used as passive repeaters
to aid in pinpointing the location of targets.
They are "passive: in that they require no power
supplies and simply pick up the Scanner's initial signal
and pass it on to the target. Initially, the primary
pair are used to triangulate in on the target.
Once the area surrounding the target is localized, the
secondary pair are used to pinpoint that target.
List Price $1500.00
New Lower Introductory Price $1199.00
Cat# 129-2022
|
Hablamos Español
Wir sprechen Deutsch
Nous parlons francais
Parliamo italiano
